| Customization: | Available |
|---|---|
| Technique: | Cold Rolled, Hot Rolled |
| Key Words: | Aluminum 1050 Alloy Sheet/Plate |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
LORK exports a wide range of monel 400 tube which performs brilliantly in large temperature and concentration ranges.
1050 aluminum alloy is a very common commercial purity alloy. 1050 aluminum has 99.50% minimum purity and the remaining 0.5% is made up of mostly iron and silicon. It was designated "Al99,5" in the earlier German DIN specifications. 1050 is a soft aluminum alloy that offers good electrical and thermal conductivity, as well as good general corrosion resistance. Aluminum 1050 a very popular material in many industries, and typically it is used in application where material's strength is not important.
Aluminium alloy 1050 is used for:
Specifications:
Aluminium alloy 1050 also corresponds to the following designations:
The following table shows the chemical composition of Aluminium / Aluminum 1050 alloy.
| Element | Content (%) |
| Cu | 0-0.05 |
| Mg | 0-0.05% |
| Si | 0-0.25% |
| Fe | 0-0.4% |
| Mn | 0-0.05% |
| Zn | 0-0.07% |
| Ti | 0-0.05% |
| Al | Balance |
Table 2. Mechanical properties for aluminium alloy 1050 H14
| Property | Value |
| Proof Stress | 85 Min MPa |
| Tensile Strength | 105 - 145 MPa |
| Hardness Brinell | 34 HB |
| Elongation A | 12 Min % |
*properties above are for material in the H14 condition
Table 3. Physical properties for aluminium alloy 1050
| Property | Value |
| Density | 2.71 kg/m3 |
| Melting Point | 650°C |
| Modulus of Elasticity | 71 GPa |
| Electrical Resistivity | 0.282 x 10-6 Ω.m |
| Thermal Conductivity | 222 W/m.K |
| Thermal Expansion | 24 x 10-6/K |
When welding Aluminium alloy 1050 to itself or an alloy from the same subgroup the recommended filler wire is 1100. For welding to alloys 5083 and 5086 or alloys from the 7XXX series, the recommended wire is 5356. For other alloys use 4043 filler wire.
Table 4. Fabrication response for aluminium alloy 1050
| Process | Value |
| Workability - Cold | Excellent |
| Machinability | Poor |
| Weldability - Gas | Excellent |
| Weldability - Arc | Excellent |
| Weldability - Resistance | Excellent |
| Brazability | Excellent |
| Solderability | Excellent |
Temper
The most common temper for 1050 aluminium is:
Aalco supplies alloy Aluminium alloy 1050-H14 as:
This Data is indicative only and must not be seen as a substitute for the full specification from which it is drawn. In particular, the mechanical property requirements vary widely with temper, product and product dimensions. The information is based on our present knowledge and is given in good faith. However, no liability will be accepted by the Company is respect of any action taken by any third party in reliance thereon.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose.
Any advice given by the Company to any third party is given for that party's assistance only and without liability on the part of the Company. Any contract between the Company and a customer will be subject to the company's Conditions of Sale. The extent of the Company's liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.
Q1: Do you accept the trial order ?
A1: Yes,if we have the exactly size in stock.we can delivery even 1 piece/meter .
Q2: Can I have free sample before making orders?
){kind=link}